- Home
- Products
- Service
- News
- Latest video
- About Us
- Contact Us
loading
GDS-118P5
Migrand
| Availability: | |
|---|---|
|
| |
How To Change The Mold of FFS Machine
Step 1：Preparations before mold removal
Step 3: Install the forming mold
4 seconds：First loosen the two tension springs in the rear compartment of the machine.
14 seconds：The middle shaft of that fix screw rod is taken as the center when the back forming mold is installed
33 seconds：After the mold is against the flat base, lock the mold set screws.
56 seconds：Install the forming die alignment plate (included in the toolbox)。
1 minute 6 seconds：Taking the level of the lower guide rail as a base line, aligning the bottle body step of the forming rear mold
2 minute 6 seconds：The position of the upper guide rail is adjusted according to the height of the bottle, and the distance between the height of the bottle and the guide rail is the same.
2 minute 18 seconds：Rail adjustment screw
2 minute 27 seconds：After the lower guide rail is adjusted, do not move it, just adjust the upper guide rail.
2 minute 40 seconds：The width of the guide must not be too tight or too loose.Ensure that the bottle is pulled smoothly and does not fall off.
3 minute 2 seconds：When installing the molding blowing module, align the side of the mold with the alignment line of the blowing block to ensure that the air hole is installed in the middle of the mold.
3 minute 25 seconds：The for front mold is arranged on that for mold fixing plate.The side of the retainer plate with the two screw holes faces the right side of the machine.
3 minute 41 seconds：Install the fixing screw into the fixing plate, align the fixing plate with the screw step, and lock the fixing plate.
3 minute 59 seconds：Tighten the retaining nut
4 minute 20 seconds：When the forming front mold is installed, the rear mold moves forward to align the bottom of the forming front mold with the lower positioning plate of the rear mold.
4 minute 20 seconds：Align the left and right edges of the front and rear molds, and then tighten the fixing screws.
4 minute 53 seconds：After installation, remove the mold alignment plate.
How To Change The Mold of FFS Machine
Step 1：Preparations before mold removal
Step 3: Install the forming mold
4 seconds：First loosen the two tension springs in the rear compartment of the machine.
14 seconds：The middle shaft of that fix screw rod is taken as the center when the back forming mold is installed
33 seconds：After the mold is against the flat base, lock the mold set screws.
56 seconds：Install the forming die alignment plate (included in the toolbox)。
1 minute 6 seconds：Taking the level of the lower guide rail as a base line, aligning the bottle body step of the forming rear mold
2 minute 6 seconds：The position of the upper guide rail is adjusted according to the height of the bottle, and the distance between the height of the bottle and the guide rail is the same.
2 minute 18 seconds：Rail adjustment screw
2 minute 27 seconds：After the lower guide rail is adjusted, do not move it, just adjust the upper guide rail.
2 minute 40 seconds：The width of the guide must not be too tight or too loose.Ensure that the bottle is pulled smoothly and does not fall off.
3 minute 2 seconds：When installing the molding blowing module, align the side of the mold with the alignment line of the blowing block to ensure that the air hole is installed in the middle of the mold.
3 minute 25 seconds：The for front mold is arranged on that for mold fixing plate.The side of the retainer plate with the two screw holes faces the right side of the machine.
3 minute 41 seconds：Install the fixing screw into the fixing plate, align the fixing plate with the screw step, and lock the fixing plate.
3 minute 59 seconds：Tighten the retaining nut
4 minute 20 seconds：When the forming front mold is installed, the rear mold moves forward to align the bottom of the forming front mold with the lower positioning plate of the rear mold.
4 minute 20 seconds：Align the left and right edges of the front and rear molds, and then tighten the fixing screws.
4 minute 53 seconds：After installation, remove the mold alignment plate.
