loading
GDS-118P5
Migrand
| Availability: | |
|---|---|
|
| |
How To Change The Mold of FFS Machine
Step 1：Preparations before mold removal
Step 3: Install the forming mold
Step 4: Install the heat sealing mold and the scrap cutter
5 seconds：Install the filling head holder, do not tighten now
37 seconds：The electric heating tube is inserted into the back heat sealing mold, and the screws of the power cord are tightened
50 seconds：Fix the post-heat-seal module without tightening it first。
1 minute 14 seconds：The bottom of the rear heat sealing mold is 2-3mm higher than the upper guide rail, and then tighten it.
1 minute 52 seconds：Install the front heat-sealing mold, insert the heating tube, install the front heat-sealing mold fixing plate into the fixing screw, and align the screw step。
2 minute 8 seconds：Tighten the heating pipe wire nut
2 minute 17 seconds：Tighten the retainer plate nut
2 minute 48 seconds：Align the front and rear heat sealing plates up and down and left and right, and then tighten the fixing nuts of the heat sealing plate
3 minute 7 seconds：After the heating tube is completely pushed into the heating plate, lock the front and rear heating tube.
3 minute 22 seconds：Restore the tension spring in the rear nacelle
3 minute 33 seconds：Installation of rear waste edge punch mold，
3 minute 48 seconds：Align the cutting mold fixing plate with the top of the back plate and tighten the screws.
4 minute 1 seconds：When installing the cutting mold, install the copper bearing in the shaft sleeve and leave half of it.。
4 minute 13 seconds：Align the pattern of the front and rear cutting mold, otherwise the knives will be damaged.lock the fixing screw.
4 minute 24 seconds：Lock nut。
4 minute 35 seconds：Check and connect the air pipe and water pipe of each module
How To Change The Mold of FFS Machine
Step 1：Preparations before mold removal
Step 3: Install the forming mold
Step 4: Install the heat sealing mold and the scrap cutter
5 seconds：Install the filling head holder, do not tighten now
37 seconds：The electric heating tube is inserted into the back heat sealing mold, and the screws of the power cord are tightened
50 seconds：Fix the post-heat-seal module without tightening it first。
1 minute 14 seconds：The bottom of the rear heat sealing mold is 2-3mm higher than the upper guide rail, and then tighten it.
1 minute 52 seconds：Install the front heat-sealing mold, insert the heating tube, install the front heat-sealing mold fixing plate into the fixing screw, and align the screw step。
2 minute 8 seconds：Tighten the heating pipe wire nut
2 minute 17 seconds：Tighten the retainer plate nut
2 minute 48 seconds：Align the front and rear heat sealing plates up and down and left and right, and then tighten the fixing nuts of the heat sealing plate
3 minute 7 seconds：After the heating tube is completely pushed into the heating plate, lock the front and rear heating tube.
3 minute 22 seconds：Restore the tension spring in the rear nacelle
3 minute 33 seconds：Installation of rear waste edge punch mold，
3 minute 48 seconds：Align the cutting mold fixing plate with the top of the back plate and tighten the screws.
4 minute 1 seconds：When installing the cutting mold, install the copper bearing in the shaft sleeve and leave half of it.。
4 minute 13 seconds：Align the pattern of the front and rear cutting mold, otherwise the knives will be damaged.lock the fixing screw.
4 minute 24 seconds：Lock nut。
4 minute 35 seconds：Check and connect the air pipe and water pipe of each module
